RouterGeek

The Cisco Routers How-To Reference


    • About RouterGeek
    • Contact Us
    • Terms of Use
    • Categories

      • General (27)
      • Hints and Tips (3)
      • Security (3)
      • 2500 Series (1)
      • 2600 Series (1)
    • Ads

    • Tags

      1600 2500 2600 3600 access-list address authentication backup boot cisco config configuration configure dhcp flash ftp global hyperterminal install interface internet ios ip isdn isp lost nat network ospf password pcmcia procedure protocol recover router routing run security sequence show start subnet tftp tips upgrade
    • Books from Amazon




    • How to Configure ADSL on a Cisco Router

        0 comments
        8th Jan 12
        Mohammed Alani

      When would you need this: When you need to configure your router to operate on ADSL line provided by an ISP.

      Special Requirements: ADSL WAN interface on the router.

      Read the rest of this entry »

        General
        adsl, atm, cisco, configure, global, internet, isp, nat, outside, router, vpdn
    • How to Configure SSH on a Cisco Router

        2 comments
        30th Dec 11
        Mohammed Alani

      When would you need this: When you need to configure your router remotely through an insecure environment.

      Special Requirements: IOS version over 12.1.3.T (with a "k9" in its feature set).

      Read the rest of this entry »

        Security
        cisco, password, router, secure shell, security, ssh, telnet
    • How to Secure Telnet Sessions Using Access-Lists on a Cisco Router

        1 comment
        21st Dec 11
        Mohammed Alani

      When would you need this: When you need to setup Telnet on a Cisco Router do facilitate remote configuration.

      Special Requirements: None.

      Read the rest of this entry »

        Security
        access control list, access-list, cisco, protect, router, security, ssh, telnet, vty
    • How to Configure Integrated IS-IS on a Cisco Router

        0 comments
        20th Dec 11
        Mohammed Alani

      When would you need this: When you need to setup dynamic routing for a large network and not all your routers are Cisco routers. It is being currently used to support MPLS routing and IPv6 routing.

      Special Requirements: None.

      Read the rest of this entry »

        General
        cisco, configuration, integrated-system, ip, ipv6, is-is, isis, mpls, nbma, router, routing, summarization
    • More About Multiple-Area OSPF Configuration

        1 comment
        19th Dec 11
        Mohammed Alani

      This article is a continuation of the previous article on Configuration of Mutiple-Area OSPF on Cisco Routers. Refer to the previous article for the essential configuration of Multiple-Area OSPF.

      Read the rest of this entry »

        General
        abr, asbr, cisco, configuration, multiple-area, network, ospf, ospf virtual link, router, subnet, virtual link
    • How to Configure Multiple-Area OSPF on a Cisco Router

        2 comments
        19th Dec 11
        Mohammed Alani

      When would you need this: When you need to setup dynamic routing for a large network and not all your routers are Cisco routers.

      Special Requirements: None.

      Read the rest of this entry »

        General
        area 0, cisco, configuration, multiple-area, network, ospf, router
    • How to Configure Single-Area OSPF on a Cisco Router

        1 comment
        10th Dec 11
        Mohammed Alani

      When would you need this: When you need to setup dynamic routing.

      Special Requirements: None.

      Read the rest of this entry »

        General
        bandwidth, cisco, dynamic, mask, open shortest path first, ospf, router, routing, subnet, wildcard
    • How to Configure a Cisco Router as a Frame-Relay Switch

        0 comments
        7th Dec 11
        Mohammed Alani

      When would you need this: When are setting up your own Frame-Relay network. Usually, it is used for lab setup.

      Special Requirements: A Cisco router with at least two serial interfaces.

      Read the rest of this entry »

        General
        cisco, configuration, dlci, frame, frame-realy, interface, router, switch
    • How to Configure HDLC on a Cisco Router

        0 comments
        7th Dec 11
        Mohammed Alani

      When would you need this: When you connect two Cisco routers through a WAN connection, or back-to-back router setup.

      Special Requirements: Both routers needs to be Cisco routers.

      Read the rest of this entry »

        General
        cisco, config, configuration, hdlc, interface, router, serial
    • How to Configure a Cisco Router as a DHCP Client

        0 comments
        8th May 07
        Mohammed Alani

      When would you need this: When your ISP gives you dynamic IP address upon each connection or you need to configure the router to obtain its interface IP address automatically.

      Special Requirements: None.

      Read the rest of this entry »

        General
        cisco, client, config, configuration, dhcp, hostname, isp, nat, provider, router
      • 1
      • 2
      • 3
      • 4
      • »
    • Search Routergeek.net

    • Follow Us


      My Great Web page
    • Our Amazon Store


      Take a look into RouterGeek Store
    Copyright © Mohammed M. Alani .All rights reserved.
    Sitemap